ZGS Pad-mounted Substation

ZGS Pad-mounted Substation — Package Substation
Pad-mounted

ZGS Pad-mounted Substation

American-style pad-mounted substation with transformer immersed in oil and fuse protection. Compact and cost-effective for residential and commercial loads.

10 kV0.4 kV50 – 1600 A
ZGS Pad-mounted Substation — Package Substation

American-style pad-mounted substation with transformer immersed in oil and fuse protection. Compact and cost-effective for residential and commercial loads.

This pad mounted substation transformer is the American-style product in the range. A pad mounted substation transformer integrates an oil-filled transformer with fuse protection in a low, compact housing for residential and commercial distribution.

How this family is built

American-style integrated construction

The ZGS type uses the American-style pad-mounted arrangement: the transformer is oil-immersed and the HV side is protected by current-limiting fuses in a load-switch / fuse combination. Integrating the transformer with the switch chamber makes the unit noticeably smaller than a European-style box of the same capacity — published figures for this construction are roughly one third to one fifth of the volume — and it sits low to the ground, which suits residential and commercial landscapes.

Fuse protection and cable connection

The HV side commonly uses a dual-fuse, full-range protection scheme: a backup fuse and an insertion fuse coordinate to clear both transformer internal faults and cable faults. Load-break elbow connectors allow the cable to be plugged and unplugged under load (a 200 A class connector is standard for this duty), which simplifies feeder switching and future extension. Both ring-network and terminal schemes can be supplied.

Where it is specified

Typical settings are new residential districts, green belts, parks, stations, hotels, construction sites and airports, on 10 kV ring, dual-source or terminal supply. The sealed tank keeps the oil out of contact with ambient air, reducing moisture ingress and insulation ageing; published low-loss designs report no-load losses about 30% and load losses about 25% below the GB/T 6451 baseline.

Common models

ZGS11-Z.G-630/10, ZGS11-Z.G-1000/10, ZGS11-Z.F-100/10

Typical parameters

ParameterTypical valueBasis
Electrical
Rated HV voltage10 kV, rated insulation level 12 kVZGS□-12/0.4 datasheet
Rated LV voltage0.4 kVZGS□-12/0.4 datasheet
Rated current50 – 1600 AZGS□-12/0.4 datasheet
Transformer capacity75 – 1000 kVA, per SLDZGS series range
TransformerOil-immersed, fuse-protected (S9 / S11 class)ZGS datasheet
HV protectionDual-element fuse, full-range protectionZGS datasheet
HV switchingOil-immersed or SF6 load-break switch, manual or motorisedZGS datasheet
HV cable interface200 A load-break elbow, hot-pluggable at 200 AZGS datasheet
Mechanical & environment
FootprintAbout 1/3 – 1/5 of a European-style unit of the same ratingZGS datasheet
EnclosureHoneycomb double-sandwich composite panel, insulated and ventilatedZGS datasheet
Ingress protectionIP54 as standardGB/T 4208
Ambient temperature−35 to +40 °CZGS datasheet
Altitude≤ 1000 m without deratingZGS datasheet
Compliance & scope
StandardsGB/T 17467-1998, DL/T 537-93ZGS datasheet
Typical useRing-network, dual-source or terminal supplyZGS datasheet

Values are the working reference for this family and its standard models. On a project the rating, protection and cable schedule are confirmed against the single-line diagram and the site conditions before the quotation is issued.

Frequently asked questions

QWhat information is needed to specify this item?
A

Send the single-line diagram, rated voltage and current or capacity, short-circuit duty, installation environment, cable or terminal schedule, and any interface dimensions that apply to the item.

QAre the parameters on this page the final project values?
A

No. They are working reference values for the product family. The final model, rating, protection, accessories and scope are confirmed against the single-line diagram and site conditions before quotation.

QWhat is included in the quotation?
A

The quotation identifies the selected configuration, bill of materials, scope of supply and applicable test or document package. Loose accessories and site work are listed separately when applicable.

QCan the item be adapted to a project drawing?
A

Project-specific dimensions, interfaces and accessories can be reviewed against the drawings. Feasibility and the final configuration are confirmed for the selected model before production.

Related systems and items

The five functional systems show what this family is assembled from; send the diagram for a project BOM.

Need this quoted?

Send the single-line diagram and the site conditions. You get back a configuration, a bill of materials and a scope of supply — in writing, at quotation.

Request a quotation
Package Substation

Specialized in package substations, switchgear cabinets and distribution components for global B2B projects. Configuration and bill of materials are fixed against the single-line diagram; assembly, wiring and routine test follow that drawing.

6 / 10 / 35 kV · 100–3150 kVA · IP54+

© 2026 Package Substation. All rights reserved.PrivacyContactmanager@packagesubstation.com
Scroll to Top